Netting to constrain insulation


S

sm_jamieson

I need some type of plastic netting to support and constrain glass
fibre insulation between 225mm joists. To support it before
plasterboarding, and to stop it from gettting pushed up too far into
the air space used for venting the roof structure.
Should be reasonably strong since the insulation may be compressed a
little.
Probably to be stapled onto timber.
Anyone know where I can get some such stuff ?
Cheers,
Simon.
 
Ad

Advertisements

V

Vortex4

sm_jamieson said:
I need some type of plastic netting to support and constrain glass
fibre insulation between 225mm joists. To support it before
plasterboarding, and to stop it from gettting pushed up too far into
the air space used for venting the roof structure.
Should be reasonably strong since the insulation may be compressed a
little.
Probably to be stapled onto timber.
Anyone know where I can get some such stuff ?
Cheers,
Simon.
A decent garden centre will sell fruit cage type netting (IIRC 4M wide) by
the metre.
 
B

Bob Minchin

Vortex4 said:
A decent garden centre will sell fruit cage type netting (IIRC 4M wide)
by the metre.
The same places and possibly ebay too will sell "pea & bean netting"
with about 100mm square mesh. Should be cheaper than fruit cage netting
and for you application, just as effective.
If you are doing other work and have any breathable membrane left over,
that can be used too.

Bob
 
A

auctions

I need some type of plastic netting to support and constrain glass
fibre insulation between 225mm joists. To support it before
plasterboarding, and to stop it from gettting pushed up too far into
the air space used for venting the roof structure.
Should be reasonably strong since the insulation may be compressed a
little.
Probably to be stapled onto timber.
Anyone know where I can get some such stuff ?
Cheers,
Simon.
Netlon insulation support netting is the stuff you need. Available by
the meter (from a 2m wide roll) from our local builders' merchants.
Some online places do it too. About 15p a square metre as far as I
remember, or cheaper by the roll.

A
 
S

sm_jamieson

I need some type of plastic netting to support and constrain glass
fibre insulation between 225mm joists. To support it before
plasterboarding, and to stop it from gettting pushed up too far into
the air space used for venting the roof structure.
Should be reasonably strong since the insulation may be compressed a
little.
Probably to be stapled onto timber.
Anyone know where I can get some such stuff ?
Cheers,
Simon.
Round here is seems they only want to sell rolls of 100m (and screwfix
make you buy 2 rolls).
Looks like the cheapest way will be to bung up some gaffer tape and a
few staples for good measure. Gaps to hold back insulation from are
only 400mm x 700mm, a couple of strips will do.
Or how about PVC Polythene Jointing Tape, all cheap from screwfix.

But - how will any of this last before it breaks down ? It would be
under slight tension, and the roofspace may get hot in the summer.
Cheers,
Simon.
 
N

NT

Round here is seems they only want to sell rolls of 100m (and screwfix
make you buy 2 rolls).
Looks like the cheapest way will be to bung up some gaffer tape and a
few staples for good measure. Gaps to hold back insulation from are
only 400mm x 700mm, a couple of strips will do.
Or how about  PVC Polythene Jointing Tape, all cheap from screwfix.

But - how will any of this last before it breaks down ? It would be
under slight tension, and the roofspace may get hot in the summer.
Cheers,
Simon.
you only need to support it till the plasterboard's up. A bit of tape
or thin wire should do fine.


NT
 
Ad

Advertisements

A

Andy Dingley

I need some type of plastic netting to support and constrain glass
fibre insulation between 225mm joists.
Screwfix sell it, designed for just that purpose. The rolls are 100m,
which is a bit excessive, and they insist you buy at least two. So
it's very cheap per metre, but you're now looking at over 50 quid!
They don't sell it at the counters either.

Toolstation do a cheap vapour barrier, which is what I used instead.
 
S

sm_jamieson

Screwfix sell it, designed for just that purpose. The rolls are 100m,
which is a bit excessive, and they insist you buy at least two. So
it's very cheap per metre, but you're now looking at over 50 quid!
They don't sell it at the counters either.

Toolstation do a cheap vapour barrier, which is what I used instead.
Why do they do that ? Its a right pain. Not many DIYers will want two,
tradesmen might though.
I'll look at the toolstation vapour barrier.
Cheers,
Simon.
 
Ad

Advertisements

T

terry

Why do they do that ? Its a right pain. Not many DIYers will want two,
tradesmen might though.
I'll look at the toolstation vapour barrier.
Cheers,
Simon.
Was going to mention.......... make sure you have a vapour barrier on
the 'warm' side of that insulation.
Otherwise warm and therefore damp laden air from the house permeates
out through the insulation and the moisture in it condenses somewhere
within the insulation. Making it damp and not very effective as an
insulator! Quite apart from potential mould/rot. Unheated areas such
as attics above should be cold and vented to/from outside.
 

Ask a Question

Want to reply to this thread or ask your own question?

You'll need to choose a username for the site, which only take a couple of moments. After that, you can post your question and our members will help you out.

Ask a Question

Similar Threads


Top