Submit Search
FREE! 2021 CALENDAR
MSI H-J3520 Cross Plate Anchor
WSO WB2751B HDG Communication Arm 3 - Position Steel Under-build, 15° Angled15 degree angled Communication arm 3 position Steel Under-build, galvanized for weather protection, and designed to allow for the addition of under-build cables. 36" inches length from poleand 12" between mount holes. All pole mounting and cable mounting holes are 11/16'' diameter.
Big-Grip Dead-ends are designed for use on Transmission, Antenna, Communications, and other types of guyed structures that require use of large guy strand.Color Code: BlackLength: 64 InchStrand Size: 5/8"Strand Construction 7W or 19WHolding Straight 42,400 - 40,200
Big-Grip Dead-ends are designed for use on Transmission, Antenna, Communications, and other types of guyed structures that require use of large guy strand.Color Code: YellowLength: 55 InchStrand Size: 9/16"Strand Construction 7W or 19WHolding Straight 35,000
The Ground Hog PSD8 Pengo 8" Auger features heat treated cast alloy steel boring heads with hardened forged steel side blades and a bolt-on cast alloy steel centered pilot bit. The Pengo Series augers are general purpose augers and are the best choice for tough soil conditions. All Ground Hog Augers are approximately 38"(3') in length and utilize a 7/8" standard square drive for interchangeability between Earth Drills.Features:
Preform Line Products Safety guy-wire dispenser is designed to provide safe, easy, completely controlled handling and paying-out of strand coils up to 500 ft in length, including EHS strand. It also can be used with wire, wire rope, cable, conductor, etc. Eliminate weight lifting, handling struggle, and the hazards of "runaway" coil ends. Small and light in weight (a carton of 50 weighs only 22 pounds), the safety guy-wire dispenser occupies minimal truck space. No banding or taping of coils is necessary. Saves personnel cost (only one person to pay out a loaded coil) and reduces inventory (just one universal size). Coil Not Included*
MSI 5201 5/16" Strand Vise, Universal Grade (Black)
MSI 5202 3/8" Strand Vise, Universal Grade (Orange)
MSI H-7187, 6-1/2" Wedge Clamp, is mechanical holding device used for strain relief in service applications. It has solid stainless bails that are used on eye hooks and insulators with a diameter larger than 1.5". This clamp is designed for low tension applications only, and also has a mechanical working load of 1,200 lbs. Specifications/Applications:
The Manta Ray load locker Manta Ray LL-1 is required to load lock and proof test the anchor. It is a double acting hollow hydraulic jack with a base reaction plate and a direct reading gauge. The load locker can be used with the same hydraulic from the line truck used to drive the jack hammer.The LL-1 uses quick release gripping jaws that grip an Adapter Setting Bar (ASB) that passes through the center of the jack. The ASB extends the anchor rod and precludes any damage to the anchor rod from the gripping jaws.
The Manta Ray load locker Manta Ray LL-1 is required to load lock and proof test the anchor. It is a double acting hollow hydraulic jack with a base reaction plate and a direct reading gauge. The load locker can be used with the same hydraulic from the line truck used to drive the jack hammer.The LL-3(50134) Base Plate is designed for anchors that are installed at an angle to the ground. It has a large bearing surface and a small cross member.The vertical legs of the Base cut into the soil during use to help keep the base from skidding.For angled guy anchors the two cross members should be placed toward the tower and perpendicular to the axis of the anchor rod. *Base Plate Only
Manta Ray 50148 LL-1TJ Tapered Jaw Set, is a key component for LL-1 Load Locker. The Taper Jaw provides grip to the Adapter Setting Bar which is pulls upward on the anchor rod and tips the anchor underground. *Taper Jaw Only*
Manta Ray 50233 SG-2, a 33" Drive Steel Extension is apatented design made of high performance materials. It allows the anchor to be driven to depth in discrete incrementsto allow installation in tight spaces while the operators remain safely on the ground. The anchor is threaded on both sides to accept a coupler for further length. The SG drive steel uses a partial left hand thread that allows very efficient impact energy transfer from the jack hammerto the anchor. All joints should be lubricated with light oil or spray lubricant prior to assembly. After installing an anchorthe drive steel joints should be cleaned of dirt which will enter the couplers during driving. Failure to clean and lubricatethe drive steel and couplers will result in premature failure.
Manta Ray 50236 SG-3, Radiused Drive Tip 30", this piece is shaped to fit into the anchor on one end and threaded on the other end to accept a coupler. The SG drive steel uses a partial left hand thread that allows very efficient impact energy transfer from the jack hammerto the anchor. All joints should be lubricated with light oil or spray lubricant prior to assembly. After installing an anchorthe drive steel joints should be cleaned of dirt which will enter the couplers during driving. Failure to clean and lubricatethe drive steel and couplers will result in premature failure.
MSI H-BVC-6 Bronze Vise Connector
Manta Ray 50424 SG-X Drive Steel Extractor Bar is used in conjunction with the LL-1 Load Locker to extract any drive steel that happens to get stuck underground. Simply remove the hammer from the shank and screw the extractor bar (it also is rope threaded) into the coupler. Use the Load Locker to pull up on the “extractor bar” to break the drive steel free. Be careful as the drive steel is pulled out and removed to not allow portions of the drive steel to fall back down the hole. Usually there is some obstruction to removing the drive steel, and once they are broken free with the Load Locker they can easily be removed by hand.
MSI H-J25088.1 5/8" Straight Suspension Clamp, with Flat Keeper Plate, is used with through bolts to serve as clamping member. This Flat 3-hole clamp securely grips messenger strand to pole, it uses a nut and square washer that is used between the clamp and pole for proper spacing.Specifications:
MSI H-J7902B Curved Heavy Duty Suspension Clamp, is constructed with curved ends to prevent damage to the messenger strand when turning small angles. It is used in conjunction with through bolts to serve as clamping member, securely grips messenger strand to the pole. A nut and square washers are used between the clamp and pole to provide proper spacing.Specifications: Firmly grips 1⁄4" (6.6M) to 7⁄16" (16M) diameter messenger strand Furnished with two track bolts and a center mounting hole constructed of high quality steel, hot-dipped galvanized Clamp Bolt Diameter: 5/8" Clamp Length: 6" Clamp Width: 2-3/16" Mounting Hole Diameter: 13/16"
H-J8163 Angled 3/4" X 14" Thimble Eye Bolt, eliminates the need for thimble,shackles,links, and guy hooks.The broad radius of the eye provides an excellent attachment point to deadend or guy messenger wire, guy strand for formed wire grips.Specifications:
MSI H-J9420 Oval Eye Bolt 5/8" X 20", is commonly used as an attachment point to secure thimbles, clevises, links, and deadend insulators. Specifications:
MSI SI-2181 Beam Clamp w/ Square Head, is used to provide an electrical connection to trailers, mobile homes or other beam structures. The cup point on bolt penetrates through surface paint or oxide for intimate ground to base metal. Specifications:
H-3M710-TC1-25 Pair Straight/Half -Tap Modular with Solid Cap Splice ConnectorsStraight/Half-Tap splice connectors permit the joining of two cables, 25 pairs at a time. They may also be used for rearranging and transferring cable without interrupting service.Features:
H-3M710-BC1-25 Pair Bridge Splice Connector Filled Module Bridge connectors are used in conjunction with either straight-only connectors or straight/half-tap connectors to permit pluggable 3-way splices, 25 pairs at a time.Features:
3M™ SLiC™ Aerial Closure has a floating bond and a rubber end seal that ensures a snug fit for cables while eliminating the need for drip collars. This 1-piece, dual-wall, molded closure is designed for construction or maintenance situations3M SLiC Aerial Closure has a floating bond and interlocking ends that expand to meet a sheath opening of any size without the use of any special kits. The 1-piece construction of this closure provides complete splice access after placement and without the removal of the closure or the bonding from a cable.
Hubbell 6452 Serving Sleeve, for 1/4" diameter strand. For holding down the loose end of guy strand projecting beyond the guy clamp. Serving sleeves have a flared end to speed application. Hot dip galvanized.Specifications: Coating: Galvanized, ASTM A-153 Material: Steel Length: 1.38"
Hubbell 6453 Serving Sleeve, for 5/16" diameter strand. For holding down the loose end of guy strand projecting beyond the guy clamp. Serving sleeves have a flared end to speed application. Hot dip galvanized.Specifications: Coating: Galvanized, ASTM A-153 Material: Steel Length: 1.50"
Hubbell 6454 Serving Sleeve, for 3/8" diameter strand. For holding down the loose end of guy strand projecting beyond the guy clamp. Serving sleeves have a flared end to speed application. Hot dip galvanized.Specifications: Coating: Galvanized, ASTM A-153 Material: Steel Length: 1.75"
Hubbell 6455 Serving Sleeve, for 7/16" diameter strand. For holding down the loose end of guy strand projecting beyond the guy clamp. Serving sleeves have a flared end to speed application. Hot dip galvanized.Specifications: Coating: Galvanized, ASTM A-153 Material: Steel Length: 2.00"
Hubbell 6456 Serving Sleeve, for 1/2" diameter strand. For holding down the loose end of guy strand projecting beyond the guy clamp. Serving sleeves have a flared end to speed application. Hot dip galvanized.Specifications: Coating: Galvanized, ASTM A-153 Material: Steel Length: 2.25"
H-J1512 Brace, Cross-arm, Span 72", Drop 22" One piece, angle steel, double span braces are used to support heavy cross-arm construction. Braces are attached to the underside of the cross-arm with 1/2" bolts or lag screws and fastened to the pole with a 5/8" bolt. The pole mounting section is designed to allow more than ample clearance for wrenching.Specifications:
Single Upset Spool Bolt 5/8" X 14" MP J2348-1/2 Minimum TENSILE STRENGTH 13,550 LBSH-J2348-1/2 Single Upset Spool Bolt
3/4" X 9' Triple Strand Anchor Rod 23,000 Minimum Tensile Strenght
MSI J8161 Angled Thimble-Eye Bolt
H-J8200-3/4/ALL19023 Burst Anchor Rod
Used for fastening poleline hardware to crossarms, poles, and other structures.
H-J8883 3/4" X 10" Double-Arming Bolt
(Limited in stock)H-J926 Joslyn Guy Clamp 2-Bolt 3/16" - 5/16" Joslyn Guy Clamps are rolled from carbon steel with straight parallel grooves that will not damage guy strand. Offset guy clamps are designed to give increase holding strength. The clamping bolts have special shoulders to prevent turning when the nuts are tightened,Specifications:
Aluma-form BGA-S25 Extra-Heavy Duty Banded Guy attachment with Clevis
H-J0870 Bust Anchor Expanding 6"
The Preformed Line Products FIBERLIGN Lite Support (FLS) system is designed to gently but firmly support All Dielectric Self-Supporting (ADSS) cable. It is intended for tangent support installations (see “LINE ANGLES”) on lines that feature low voltages, very short spans and low mechanical loads. For products with higher capabilities see the subsequent pages under FIBERLIGN® Dielectric Support, FIBERLIGN Aluminum Support, FIBERLIGN Aluminum Suspension, with and without rods and FIBERLIGN Dielectric Suspension. The two latter products can be used in higher voltage environments where track resistant ADSS cables.Cable Diameter: Minimum: .550" (14 mm) Maximum: .579" (14.7 mm)
Preform Line Products Safety guy-wire dispenser is designed to provide safe, easy, completely controlled handling and paying-out of strand coils up to 500 ft in length, including EHS strand. It also can be used with wire, wire rope, cable, conductor, etc. Eliminate weight lifting, handling struggle, and the hazards of "runaway" coil ends. Small and light in weight (a carton of 50 weighs only 22 pounds), the safety guy-wire dispenser occupies minimal truck space. No banding or taping of coils is necessary. Saves personnel cost (only one person to pay out a loaded coil) and reduces inventory (just one universal size). Coil not included*
H-J8830 5/8 X 30 Square Head Machine Bolt
Lineman's High-Leverage Ratcheting Wrench features the most durable ratchet. The ratcheting wrench has a built-in strike face available in both milled and smooth, providing you with a dedicated surface for hammering. This MILWAUKEE® ratchet wrench also has a large directional switch that you can easily press while wearing gloves. These wrenches are constructed from durable forged steel for longer tool life. The high leverage wrench fits 3/4", 1", and 1-1/8" square hardware.
MILWAUKEE® Lineman's 5-in-1 Ratcheting Wrench features the most durable ratchet. The ratcheting wrench has built-in strike face offered in both milled and smooth, providing you with a dedicated surface for hammering. These wrenches have large directional switches that you can easily press while wearing gloves. The durable forged steel construction provides you with longer tool life. The wrench fits 3/4", 1", and 1-1/8" square sockets and 9/16" and 3/4" standard sockets.
H-4069 Crossover Clamp for 1/4" Strand
H-982/SI-7512-025 Bell Cable Spacer 1/4"
1-1/2" TWIN SOLID SQUARE HUB 10" HELIX POWER DRIVEN ANCHOR - 6000 FT. LB. FOR 3/4" AND 1" RODS
H-J8162 Angled 3/4" X 12" Thimble Eye Bolt, Used for dead-ending and attaching guy wires to poles and crossarms. Eliminates the need for thimble,shackles,links, and guy hooks.The broad radius of the eye provides an excellent attachment point to deadend or guy messenger wire, guy strand for formed wire grips.
H-J8164 Angled 3/4" X 16" Thimble Eye Bolt, Used for dead-ending and attaching guy wires to poles and crossarms. Eliminates the need for thimble,shackles,links, and guy hooks.The broad radius of the eye provides an excellent attachment point to deadend or guy messenger wire, guy strand for formed wire grips.
H-J8165 Angled 3/4" X 18" Thimble Eye Bolt, Used for dead-ending and attaching guy wires to poles and crossarms. Eliminates the need for thimble,shackles,links, and guy hooks.The broad radius of the eye provides an excellent attachment point to deadend or guy messenger wire, guy strand for formed wire grips.
Hubbell C3031836 Digital Torque Indicator with Display
Digital Wireless Torque Indicator with wireless display
PLP GDE-1104LA 1/4" Dead-End Guy-Grip, Light Application - "A" Coat
One-piece V-type crossarm brace is fabricated from angle steel and provides heavy-duty support for crossarm stability.
H-J8832/ALL8928 Machine Bolt with Nut 5/8" X 32"
Closure, Aerial, Kit With Floating Bond And Spiral End Seal 3x33, 3M Closure, Aerial, Kit With Floating Bond And Spiral End Seal 3x33, 3M Features fewer parts and easier installation with the 3M SLiC Aerial Closure, Superior seal, Easily adaptable, Single piece design, Double wall molded construction, Made from durable, rugged materials, Easy to access and reenter. Additional Information Standard Package Quantity: 1.0 each Gross Weight: 5.8000 lbs Product Number SLIC3.6X33SESSLIC AERIAL CLOSURE 400 PAIR 3MSLIC3.6X33SES
3M™ SLiC™ Aerial Closure has a floating bond and a spiral-end seal that ensures a snug fit for cables while eliminating the need for drip collars. This 1-piece, dual-wall, molded closure is designed for construction or maintenance situations.
Fiber Tag Generic (No Company name) 4 Inches long fits 1/2" to 1" line. Caution Fiber Optic Cable tag ACP-DN-33-4-ORANGE